SupaVoxel
Free 3D printing tool

Miniature Base STL Generator for Any Figure

Drop a figure, pick round, hex or square, and watch the base resize live under its feet. Download model and base as one STL or 3MF. Free, no account, and the file stays on your device.

Drop your .stl here

Put a round, hex or square plinth under a miniature or figure and export it as one STL.

STLOBJGLBGLTFFBX3MFPLYUSDZDAESTEP

Runs in your browser — your file never leaves your device

  • Round, hex or square
  • Live preview
  • One fused STL or 3MF
  • No sign-up

By ·Updated

01

How to add a base to an STL in 3 steps

  1. 01

    Drop the figure

    Drag an STL, OBJ, GLB, glTF, FBX, 3MF, PLY, USDZ, DAE or STEP file onto the tool above, up to 200 MB. Scale it to its final size in your slicer or modeling app first, because the base is sized from the model. Try a sample loads a 120 mm bust.
  2. 02

    Shape and size the base

    Choose Round, Hex or Square, then drag Size vs. footprint and Thickness vs. model height. There is no run button: the preview updates as you drag, and the panel shows Base diameter (or Base width) and Base thickness.
  3. 03

    Download one file

    Click Download STL or Download 3MF. If the model is a closed solid, model and base are fused into one watertight part. If it isn't, they come out as overlapping shells, which slicers merge on their own.
02

STL base generator settings

Shape

Range
Round, Hex, Square
Default and advice
Round. Hex and square are sized so their flat edges still clear the feet

Size vs. footprint

Range
105–220%, steps of 5%
Default and advice
130%. The footprint is the outline of the bottom 5% of the model seen from above. Use 105–115% for a tight base, 150% and up for a scenic one

Thickness vs. model height

Range
2–20%
Default and advice
6%. On a 32 mm figure that's about 2 mm; 11–12% gives the 3.5–4 mm of a standard plastic base

Edge

Range
Fixed
Default and advice
The top is 94% as wide as the bottom, a slight bevel like a stock wargaming base

Join

Range
Automatic
Default and advice
The model sinks slightly into the base so the two print as one piece
SettingRangeDefault and advice
ShapeRound, Hex, SquareRound. Hex and square are sized so their flat edges still clear the feet
Size vs. footprint105–220%, steps of 5%130%. The footprint is the outline of the bottom 5% of the model seen from above. Use 105–115% for a tight base, 150% and up for a scenic one
Thickness vs. model height2–20%6%. On a 32 mm figure that's about 2 mm; 11–12% gives the 3.5–4 mm of a standard plastic base
EdgeFixedThe top is 94% as wide as the bottom, a slight bevel like a stock wargaming base
JoinAutomaticThe model sinks slightly into the base so the two print as one piece

All sizes are in your file's units, usually millimeters. If a model stands on a single point, the base never shrinks below about a third of the model's width.

03

Miniature base STL sizes: 25 to 50 mm

Size the base to the game you play, not just to the sculpt. Move Size vs. footprint until Base diameter reads the number you need; with 5% steps you land within about a millimeter on a typical mini.

25 mm round or square

Typical use
Small and Medium creatures in D&D, which fill one 5-foot square, drawn 1 inch wide on most battle maps
Stock base for reference
25 mm across the bottom, 23.8 mm on top, 3.5 mm tall

32 mm round

Typical use
Heroic-scale infantry in many wargames
Stock base for reference
31.6 mm bottom, 29.4 mm top, 4 mm tall

40 mm round

Typical use
Bulkier infantry, heroes and characters
Stock base for reference
39.6 mm bottom, 38.6 mm top, 4 mm tall

50 mm round or square

Typical use
Large creatures in D&D (2 by 2 squares) and small monsters
Stock base for reference
49 mm bottom, 47.3 mm top, 4.2 mm tall
BaseTypical useStock base for reference
25 mm round or squareSmall and Medium creatures in D&D, which fill one 5-foot square, drawn 1 inch wide on most battle maps25 mm across the bottom, 23.8 mm on top, 3.5 mm tall
32 mm roundHeroic-scale infantry in many wargames31.6 mm bottom, 29.4 mm top, 4 mm tall
40 mm roundBulkier infantry, heroes and characters39.6 mm bottom, 38.6 mm top, 4 mm tall
50 mm round or squareLarge creatures in D&D (2 by 2 squares) and small monsters49 mm bottom, 47.3 mm top, 4.2 mm tall

D&D sizes follow the 2024 rules. Games Workshop round bases are stock measurements as of October 2026. For tournament play, use the base size your game sets for that unit.

04

Which base suits which figure

Painted miniatures on printed round, hex and square bases, primed with the figure as one part
Chibi figures with big heads need a wider base, 150% or more, to stay upright
A robed figure with a wide hem only needs 110–120% for a clean, tight round base
Squat chibi figures stand fine at the default 130%; pick Hex for games played on hex maps
05

Printing a miniature with its base

A fused miniature base STL solves two problems at once: the figure gets a large flat face on the build plate, and there's nothing to glue afterwards. On an FDM printer, print it upright on the base. On a resin printer, most people still angle and support the whole part, but the base gives supports a solid landing and makes the finished mini stand.

If the download message says model and base were exported as overlapping shells, the model has holes or flipped faces. Slicers merge the shells and print them fine; for a single clean solid, fix the figure in STL repair first. Thin ankles are the usual weak point, and a slightly thicker base sinks the feet deeper.

06

Add base to STL: tips for a clean print

Do
  • Scale the model to its final height before you add a base, since every size is relative to it
  • Check the Base diameter readout against the size your game lists
  • Raise the thickness to 11–12% on 28–32 mm minis for a stock-looking base
  • Download 3MF if your slicer is Bambu Studio, PrusaSlicer or Cura, which keep units in 3MF
Avoid
  • Add a base to a model that floats above the ground; the tool sizes from its lowest 5%
  • Expect ovals, rectangles or magnet holes; it makes round, hex and square only
  • Base a broken scan without repair if you want one watertight part
07

What this miniature base STL tool doesn't do

  • Three shapes only. No ovals, cavalry rectangles, textured tops or engraved text.
  • Relative sizing. You set the base as a percentage of the footprint in 5% steps and read the result in millimeters; you can't type an exact diameter.
  • Footprint from the bottom 5%. A model posed on a rock or with a cape trailing to the ground gets a base sized to everything in that slice.
  • File units. The tool doesn't convert inches or meters.

Need the figure itself? Generate one from a picture with the miniature generator or image to STL, then come back to base it. The studio also has a stand-base generator for models you make there.

FAQ

Frequently asked questions

How do I add a base to an STL file?

Drop the STL onto the tool above, choose Round, Hex or Square, and drag Size vs. footprint and Thickness vs. model height until the readout shows the base you want. The preview updates live. Click Download STL or Download 3MF and you get the figure and its base as one file, ready to slice.

What size base should a miniature have?

It depends on the game. In D&D, Small and Medium creatures fill one 5-foot square, drawn 1 inch wide on most maps, so a 25 mm base fits; Large creatures take 2 by 2 squares, about 50 mm. Wargames list a base size per unit, commonly 25, 32 or 40 mm round for infantry.

Is this miniature base STL generator free?

Yes, with no account, watermark or limit. The base is built and joined to your model by WebAssembly running in your browser, so the file is never uploaded. That also means purchased or Patreon miniatures stay on your computer, which matters if their license doesn't allow sharing the files.

Will the model and base print as one piece?

Yes. The model sinks slightly into the base. If your file is a closed solid, the download fuses both into one watertight part. If it has holes, you get two overlapping shells in one file, which every common slicer merges into one print. Repairing the file first gives you the single solid.

Can I make a hex base for board games?

Yes. Choose Hex and the base is sized so its flat edges still clear the figure's feet. The readout shows its diameter corner to corner. Square works the same way for grid-based games, with Base width shown instead of diameter.

Why is my base the wrong size?

The base is sized from the model, in the file's own units. If the model is not yet at its final scale, or the file is in inches or meters, the millimeter readout won't match your table. Scale the figure to its final height in your slicer or modeling app, export it, and drop it in again.

Can I add magnet holes or an oval base?

Not in this tool. It makes round, hex and square bases with a slight bevel. For magnets, subtract a cylinder in your slicer's negative-part feature, or drill the printed base. Oval and rectangular bases would need a CAD tool such as Blender or Fusion.
Start free

Add a base to your miniature

Drop a figure into the miniature base STL generator above and download it with its base as one printable file.

Free · runs in your browser · no sign-up